| 60TRL02B NSK Thrust Tapered Roller Bearing | RG:1/2 NPT; Taconite seal:TER 120; Housing:SAFS 028 KA; Mass pillow block:60.3 kg; R1:79.375 mm; Initial grease fill:379.89 g; Appropriate attachment bolt size G:0.75 in; ba:53.975 mm; P90°:149 kN; A1:120.65 mm; Stabilizing ring:2 x 36053-50; J1:69.85 mm; H2:53.975 mm; Pa:22.2 kN; P150°:87.2 kN; Max. speed for Taconite seal:625 r/min; h:46.038 mm; P60°:249 kN; da:122.237 mm; Ca:72.619 mm; |
| 692TFX01 NSK Thrust Tapered Roller Bearing | B:20 mm; Basic static load rating C0:90 kN; dk:35.5 mm; h1:94 mm; l7 min.:30 mm; α:7 °; w:30 mm; l4 max.:128 mm; Mass rod end:0.65 kg; d:25 mm; C1 max.:18 mm; r1 min.:0.6 mm; l5 ≈:18 mm; l3 min.:36 mm; Basic dynamic load rating C:48 kN; d2 max.:65 mm; Specific dynamic load factor K:100 N/mm²; d4 ≈:35 mm; G:M 24x2; Material constant KM:330; |
| 320TFX01 NSK Thrust Tapered Roller Bearing | RG:1/4-28 UNF; Hexagonal key size for grub screw N:3.969 mm; A5:26 mm; GN:1/4-28 SAE-LT; Recommended tightening torque for grub screw:6.5 N·m; Thread grub screw G2:5/16-24 UNF; Basic static load rating C0:19 kN; DN:6.5 mm; Recommended diameter for attachment bolts, inch G:0.5 in; J7:34 mm; d:36.512 mm; Fatigue load limit Pu:0.8 kN; Db1:98 mm; Basic dynamic load rating C:30.7 kN; J:101.5 mm; |
| 30RCV17 NSK Thrust Tapered Roller Bearing | Sealed Speed Rating n3:0 rpm; Grease Speed Rating Open/Shielded n1:2400 rpm; Accessories:Without Accessories; Basic Static Radial Load Rating Co:76500 N; D:225.0000 mm; Oil Speed Rating Open/Shielded n2:3000 rpm; Basic Dynamic Radial Load Rating C:62400 N; Fillet Radius ra:1.00 mm; B:22.00 mm; d:180.000 mm; |
| NN393 NSK CYLINDRICAL ROLLER BEARING | Tolerance shaft:e7; Coefficient of friction µ max.:0.15; Coefficient of friction µ min.:0.08; Mass bushing:3.85 kg; D:160 mm; Tolerance housing:H7; Permissible sliding velocity v min.:0 m/s; α:124 °; d:140 mm; a:4.5 mm; B:90 mm; Permissible sliding velocity v max.:0.5 m/s; Specific static load factor K0:45 N/mm²; h:142 mm; Specific dynamic load factor K:25 N/mm²; |
| NNU3038 NSK CYLINDRICAL ROLLER BEARING | A2:149.225 mm; R1:60.325 mm; A1:98.425 mm; Mass pillow block:31.3 kg; P120°:53.4 kN; End plug (suffix Y):EPR 11; P180°:58.7 kN; Cap bolt recommended tightening torque:149.1 N·m; R2:27.781 mm; PG:1/8 NPT; H1:101.6 mm; L:349.25 mm; P60°:141 kN; Stabilizing ring:SR-18-15; Cap bolt, SAE grade:8; H:196.85 mm; H2:41.275 mm; Initial grease fill:141.75 g; da:77.787 mm; ba:40.481 mm; |
| 377TFV01 NSK Thrust Tapered Roller Bearing | Basic dynamic load rating C:77 kN; A:60.325 mm; da:42.862 mm; J max.:161.925 mm; S:0.794 mm; d2:68.659 mm; H1:53.975 mm; Limiting speed:5300 r/min; s:25.4 mm; Mass bearing unit:4.22 kg; H2:31.75 mm; B:73.025 mm; L:200.025 mm; Attachment bolt diameter G:12.7 mm; A1:78.581 mm; J min.:155.575 mm; H:107.95 mm; |
| NN4930K NSK CYLINDRICAL ROLLER BEARING | P90°:370 kN; P120°:280 kN; Tightening torque for grub screws:8 N·m; Mass bearing unit:21 kg; P55°:620 kN; Fatigue load limit Pu:39 kN; S:2.5 mm; Pa:35 kN; N4 max.:8 mm; L:380 mm; J:320 mm; H1:112 mm; N1:26 mm; Limiting speed:1050 r/min; P150°:250 kN; Attachment bolt diameter G:24 mm; A:110 mm; Tightening torque for attachment bolts:665 N·m; Bearing mean diameter dm:125 mm; |
| B700-1 NSK Angular contact ball bearing | r5 min.:0.6 mm; Abutment housing - axial space at the small side face/ both sides of the outer ring Cb min.:6 mm; t:2 mm; Calculation factor Y2:2.9; Reference speed:4000 r/min; Abutment diameter shaft db min.:74 mm; r1,2 min.:1.5 mm; Limiting speed:6300 r/min; Fillet radius rc max.:0.6 mm; Calculation factor Y0:1.8; a:48.011 mm; l:6 mm; Calculation factor e:0.35; Calculation factor Y1:1.9; Abutment diameter shaft Db min.:96 mm; |
| NNU3134 NSK CYLINDRICAL ROLLER BEARING | H1:95.25 mm; da:71.438 mm; R1:53.975 mm; Cap bolt, SAE grade:8; PG:1/8 NPT; P120°:28.9 kN; End plug (suffix Y):EPR 9; Initial grease fill:110.56 g; J max.:279.4 mm; P180°:32 kN; Pa:9.25 kN; Taconite seal:TER 51; A1:88.9 mm; H2:38.1 mm; P150°:26.7 kN; Da:150 mm; Cap bolt:2 x 5/8-11 UNC; H:187.325 mm; Housing:SAFS 517; Appropriate attachment bolt size G:0.75 in; |